Thursday, January 1, 2009

Building a Pirate Ship - Part 5

Part 5:

Adding details to your pirate ship.

Up to this point most of the work has been shaping and adding the various parts of the ship. In this installment I will outline the steps required to detail the removable quarterdeck piece.
  • The primay tool needed is a fine saw tooth blade, which can be fitted into a standard exacto knife.


Cut out the captains door:


This piece is about 3/4 inch wide by about 1 inch tall. I have made this piece about a 3/8 inch thick, however i did not measure the it. Just rough the demension by look. Start by cutting a larger square, they trim the piece, round the top, and place it on the face of the quarterdeck piece.




Tool in the door frame:
The door frame grove seen on the left, is made by pressing the tool into the "door" piece cut in the previous step. Pressing the details into the door, also serves to bond the door to the quarterdeck face.




Also notice I have added three vertical "panels", to form the door.



Adding the wood grain:
This technique you will use repeatdly as you add wood grain to nearly all surfaces of the ship. Here I am adding the wood grain horizontally to the left of the captains door on the face of the quarterdeck. I alternate with horizontal and vertical wood grain as needed.


For example the bevel cut area is vertical wood grain, while the side and inside are all horizontal.


Add port holes:
The port holes are created by adding a bead of clay in a circle. Then I press a compacting dental tool into the bead to form rivets.


If you do not have access to dental tools, then cut the pointed tip from a tooth pick and use the cut end to make your rivets.

Notice on the left bulkhead, I have added vertical lines, to look like panels, before I added the port hole.

=> Also press a circle into the clay inside the porthole to give it the illiusion of depth.

  • Do not however, pull an actual hole in the clay. Later I will demostrate painting the port hole sky blue with clouds to make it look like it is reflecting the sky in a translucent or semi translucent glass window.


Adding the wood grain deck:
With the saw tooth blade, add wood grain on the top of the quarterdeck. Then add, wood decking, with the edge of the saw blade, or with a fine edges tool.

The tool show here is the dental compact tool mentioned above. It works great for adding rivets at the ends of each deck plate. Notice how I have added the deck plates in a pattern to make it look like different length of planks had been used to build the ship.

=> The "rivet" marks on the wood planks would represent wood pegs, bolts or nails depending on the area of the ship. For ease of explaination, I will call them "rivets" as a general term, since that best describes the hundrens of little holes you will make on the decks.


Add wood grain on all surfaces:
Add the wood grain and the plank details on the side, and even on the underside. Also add the rivet marks on each plank.

Notice the two vertical boards on the beveled section, which each have only one rivet mark on the top and bottom.

= >Use your creativity with the wood grain, planks and rivet marks. At times I will even add battle damage on ships, or carve speical features, skulls, or other marking to give each ship more character.


Add a railing:

I have used small skewer sticks, carved a grove in the stick, then worked a point to creat this post rail. This too is rather tedious work, however I like the customer look to the post once finished.

Notice I have four holes in the deck, made with a deep plunge of the dental compact tool.

=> I strongly suggest to cut the sharp tips off the skewer sticks. The fine point will draw blood while you work details, adding chians, ropes and rigging. If you intend to use the ship for gaming, it could also cut a careless finger. Trust me on this one, I cut the shape tips off all the skewers or tooth picks used on my ships now. Your finger tips and knuckles will thank you for this suggestion.



Install the rail:

Push the four posts into the clay, using the four guiding holes shown in the previous picture.

Work the post in slowly, twisting as you go to avoid crushing the bulkhead, or mis-forming the deck.

=> Also do not push them in to far, or you will have a post in the port hole. The post on the far left, did just that, so I had to rework the port hole.

  • You can also add hinges and a door knocker if you like to add that special touch. The door knocker on this ship is a skull. You can look back on the finished picture above to see the finish details added.

Concluding part 5:

This concludes part FIVE of the Pirate ship build. The next installment will prepare the main deck, and exterior hull for the wood grain and plank details. I will cover in detail, how to strengthen the mast supports, working to bring life to your pirate ship.

Thanks for following the Blog!!

John T Cusack

www.battlefieldhobbies.org

Posted by Picasa

Building a Pirate Ship - Part 4

Part 4:

Creating the gun ports.

Up to this point, I have walked through the steps of building the basic hull, adding the stern, forecastle, spar deck and creating the removeable quarterdeck.

In this installment, I will cover cutting in the gun ports, adding a temporary fore mast and main mast, then the creating of steps leading up to the Quarterdeck. When you get right down to it, the gunports MAKE the ship!


Test figures:
Select a 25mm figure from your collection. If you do not have any figures, pick up a pirate figure from your local Game/Hobby store.

The Figure I use, is primed, however not fully painted. It should however, be mounted on a base like those you may use in your figure collection. The one shown is on a 1 inch masonite base.

In addition, I have selected a deck gun (Cannon) which has a barrel that measures 30mm in length.



Measure the gunwale:
This is by far one of the most important steps. As you work the model, the sides droop, stretch and otherwise become mis-shaped. Througout the entire build, I work and re-work the side of the ships. As you cut gun ports, the side will "sag" even more. So for this reason I stress, this is important, so measure, now then measure again, and again, before you bake the model.

=> I use a doll rod, with a red mark at 1-1/4 inches. Hold the measuring stick all along the side. Correct any areas that are below the mark.



Prepare the main deck:

With your fingures, flatten the main deck to remove any bumps of rounded areas. This step will make the workable main deck surface larger, at the same time ensuring the surface is flat.

You will want to flatten the surface very well, while spot measuring the gunwales throughout this step. I even use the "test" figures since the 1 inch round base helps to level off the main deck surface. All the more reason to use an unpainted figure.



Mark the gun ports:
Using the deck gun, place and press the barrel into the side of the ship. Take note in the picture you can clearly see the first two locations, to the right of the deck gun piece.

I suggest using an unpainted deck gun too, since clay will often stick to the piece.

Mark out each gun port, for this ship I have eight ports, with four on the port and four on the starboard gunwale.


Cut the gun ports:
Using a flat, square ended tool, press the gun port by forming a square in the side of the ship. While pressing the tool, you will need to place you fingure on the outside of the ship to support the gunwale. Press until you feel the flat, square edge against your finger.

Once you have press "cut" the four sides, push the piece through from the inside. It will make a rough square hole. Take only a moment to square off and clean the gun port. There is still some detail wrok to be done later, so you do not need to have the gun ports perfect at this point.

=> Test fit the deck gun at each gun port hole to ensure it is lined up correctly.



Insert temporary masts:
Using a short doll rod, insert the foremast, then insert the main mast into the mast supports.

When baking you will use these temporary mast, later I will demonstrate the placement of the actual full lenght masts to provide vertical alignment of the the mast.

=> The doll rods for the foremast can be 1/4 inch or 5/16 inch. The main mast, I like to use a 3/8 inch doll rod, since it will be taller it should be thicker at the base.


Forming the steps:
The steps are only for show, and will not be made for figure placement. Star with a small piece of clay, I like to star with a lump or ball, then cut it down, verse flattening a piece of clay. I find that using a ball of clay is best, carefully worked with your hands to remove any air pockets.

Cut a small square, about 1/2 inch thick by 1 inch square. Cut the piece from as shown, from corner to corner.


Trace the step pattern:
With a flat, square ended tool, lightly trace the step pattern. Don not cut the pattern, only mark it so you can see the pattern on the side of the steps.

=> Nothing too fancy, again this piece is only for show.




Install the steps:
Place the steps against the side/gunwale, with the pattern you traced showing. Then with a flat, squared ended tool, push the pattern into the steps. Do this while working the clay into the side/gunwale seam.

Work the bottom seam, blending the clay into the main deck and sides of the ship.
=> Do not bond the steps with the removable quarterdeck. In fact, remove the quarter deck and work the back seam, forming a clean fit.

  • Note: You will recall the beveled edge I had mentioned in a previous step. As I recommended earlier, matching a flat quarterdeck face with a flat backing on the steps will make the removable quarter deck much easier to fit together. I have made a beveled edge, which took many test fittings and work to gain a fit like a "key" for my removable quarterdeck. Since my ships are all hand made and customized, I like to have a "key" type fit for the removable deck. But again, I suggest a flat cut for your first ship.

Concluding Step 4:
This concludes part FOUR of the Pirate ship build. This is the final "rough" build section, before I move on to showing you how to add the fine details that will bring your ship to life.

In the next installment I will cover adding detail to the removable quarterdeck and Captains cabin doorway and port holes.


  • How is your build going?
  • Post comment on your progress, tips for your fellow craftsmen, comments or question.

As a master craftsmen, teacher and artist myself, I have a goal to learn something new each day. Thus far every day is successful, as I learn every day with every new project. Today could be your day to teach me a tip or technique that you have picked up along the way. Be confident to share what you have learned, it helps build the artists community, and who knows, some day you will be the master, and I but the student.

I hope you are enjoying the instructions, and learning a few tips along the way.

John T Cusack

www.battlefieldhobbies.org

Wednesday, December 31, 2008

Building a Pirate Ship - Part 3

Part 3:

Creating the forecastle.

In part two, I showed you how to add the stern and how to prepare the quarterdeck section for the removeable quarterdeck.

In this installment, I will step you through the process of adding the forecastle, bowspar, creating the removeable quarterdeck and finsihing up with the post support for the main mast.

As in part 1 & 2 you will begin with a completed picture of the pirate ship that this will be outlined in part 3.

Cutting the forecastle deck pattern:

Flaten a small piece of clay, make the thickness of this section about 3/4 to 1 inch thick. This is by far the thickest piece we will be cutting.

You may find that this piece does not fit the bow area perfectly. The extra thickness will allow you to mold it into the area, creating a forecastle deck area large enought for one of two 25mm figures.

=> You will note in later pictures, I often use a "test" figure to help keep the model in perspective. I also use a 1:72 scale deck gun, to help align the gun ports.


Place the forecastle deck:

Align the forecastle deck in the prow of the ship. You will notice that in front of the deck piece is small open space. You will recall in part one, this the area you had placed an extra ball of clay to fill in and streghten the bow of the ship.

=> The deck should be slightly below the edge of the ship gunwale/side.


Use a flat, square tipped tool, to adhere the clay to the main deck. You will notice that while bonding the clay, I have created an underscored area below the deck. This will be the bulkhead area of the forecastle deck. Also work the seams, and blend the clay from the deck into the sides of the ship. Add beads of clay as needed.

=> Optional: I will often add a bulkhead door, below the forecastle deck, assuming the deck is thick enought. With this ship however, I have not added this feature, since I have added the foremast support in this location instead. If you would like to add a door, just make your forecastle deck an extra 3/4 inch wide and insert the bow support on top of the forecastle deck.


Adding the bow spar:

It is now time to add the first of many wood piece parts to the ship. I have selected a doll rod 5/16" in diameter that is 6 inches long. I have tapered the doll rod on one end, however this is very tedious work, shaving and sanding the tapered doll rod. You can also purchase tapered doll rods to save time and effort if you must.

Insert the bow spar along the prow, and push the end at least 1/2 inch into the clay of the forecastle deck.

Installing a Spar deck:

To help ensure the removable bow spar is strong enough to support the spar, and last for many years, I have added a spar deck.

Cut a small elongated trapezoid shaped deck, approximately 1/2 inch in thickness and about 3/4 inch wide.

This small spar deck will allow you to place a forward lookout, while providing the much needed support for the bow spar.



Installing the foremast support:

Cut a small square, tapered on the side and front and flat across the back. The flat side will be bonded to the forecastle deck.

This is going to support the foremast, so it must be at least 3/4 inch square, and about 3/4 to an 1 inch thick.

=> Bigger is not always better, so keep the post reasonable sized. We are going to add wood later to help strengthen this piece.

Tool the foremast support:

Use a flat, square ended tool to secure and bond the piece to the main deck.

Then blend the piece into the bulkhead of the forecastle deck. Try to keep the support piece larger at the base.

Again, we will add wood supports to this piece later, however make sure you keep the piece large enough to have a 5/16 inch doll rod inserted for the foremast.

Cutting the Quarter Deck and bulkhead:

Flatten a piece of clay, keeping the thickness about 1/2 inch. Make this piece large enough to not only cut to the two pieces show, but also enough to cut two additional side pieces.

The main deck is a trapezoid shown above, with the bulkhead below, marked in the picture as the "Qtr Deck face". You will notice my pattern is too small. This is in part, is because my ship is wider then the sloop/schooner pattern I used to cut the main deck. Also in part, since as you tool, flatten and work the clay, it tends to stretch.
This is ok, since the extra main deck space is useful if you plan to use the ship with figures for gaming.

Building the removeable quarterdeck:

Place the bulkhead piece face down, and connect the piece to the quarterdeck. Use a round flat tool (my favority tool) to blend the clay together. This is the inside, so do not hesitate to add an extra bead of clay if you must to help connect these two pieces.

Keep the deck at a nice 90 degree angle to the bulkhead face, working the clay seam to ensure a nice clean fit.

Also blend the outside seam on the face of the bulkhead, to ensure a nice smooth finish.

Cut the side bulkheads:

Cut out two lengths of of clay for the side. You will need to measure the width. You can test fit the piece and trim the edge as needed to match the sides with the face.

The sides will be placed with the quarterdeck face down on the work surface. Use your tools to blend the seam, both inside and outside.

Add a bead of clay inside:

I have opted to add a bead of clay along the inside seam on this piece. Since the inside is not seen, the strenght of the piece is more important then how the piece looks inside.

This will help bond all the seams. Notice that I have added a bead of clay on both the horizontal and vertical seams.

Use your tools to blend the bead into the deck and bulkhead surfaces.

Install the removeable Quarterdeck:

Place the removeable quarterdeck at teh stern of the ship. As needed, trim and form the deck to ensure that it fits into place.

The seam between the stern, quarterdeck piece and the removebale quarterdeck should be flush. It does not however need to be a tight fit, since this deck needs to remain independant of the rest of ship.

As we work details into the ship, this piece will be removed and installed several times. You may notice that I have belvel cut the two front corners of the piece. This is done to allow the steps to be placed, and it also forms a "key" type match of the removeable quarterdeck onto the ship deck. Once the steps are build, I had to make many adjustments to ensure the correct fit. If the "key" shape of teh belved deck and steps do not fit properly, the removeable deck will not be removeable.

=> I would suggest to keep the face of your removeable quarterdeck piece flat. It will make it easier to fit the removeable pieces later. The belve looks great, yet it can be a trouble area that can be easiliy avoided.

Installing the Main mast support:

Make a ball of clay, a little smaller than a golf ball. Then cut out a 1 inch thick trapezoid shaped support post. Notice that the post is wider at the top and larger at the bottom.

Also I have made this support post about 1-1/2 inches wide by about 1 inch depth, by at least 1 inch tall at teh base.

This support post is going to be for the main mast, and later I will show you how to add wood support to help strengthen the support piece.

Tooling the Main mast support:

Before you place the support piece, I have "roughed up" the underside of the piece with a saw tooth exacto blade. This helps the the piece bond tot he main deck. Since this piece MUST adhear firmly tot he main deck, the rough underside surface will help hold the piece in place.

Use the center lines on the main deck to help place the support post in the correct location.

Use a flat, square edged tool to blend the clay from the post onto the main deck. I have not added a bead, however if you need a bead do so to help blend the post to the deck. This piece needs to be strong, since it will support the main mast, which will be removed and placed many times over the life of the model.

=> Again, later I will show how to add extra wood to support this piece, yet the clay alone should be strong enough to support the main mast.


Concluding part 3:

  • This will conclude Step THREE of how to build a pirate ship by hand. Below you can see that the model is finally taking shape and starting to look like a ship. The grid lines on my work surface are 1/2 inch squares. So you can see that the ship is 13 inches bow to stern, plus 3-1/2 inches of bow spar extension at the prow. Once you place the rudder this ship will measure 17 inches by about 6-1/2 inches at the widest point. By approxiamte scale, this would make our ship about a 100 to 110 foot in length. Not bad for a fast and manuverable pirate ship.

In the next installment, I will demostrate how to add the gun ports and how to add steps that lead up from the main deck to the quaterdeck.

  • By the way, if at any point you need a few extra tips on the build, drop me a line or post comment and I will address your questions. The purpose of this tutorial is for YOU to learn the steps needed to create your own pirate ship. As with any instruction, when in doubt, just ask a question.

John T Cusack

http://www.battlefieldhobbies.org/

Posted by Picasa

Building a Pirate Ship - Part 2

Part 2:

Building the Stern, and quarterdeck.

In the first part, I showed you how to begin your pirate ship project, with basic art supplies, tools, and materials needed. In addition I went on to explain how to cut the patterns for the hull and gunwales.

In this installment, I will step you through the process of adding the stern and preparing the quarter deck. One step at a time, and you will be able to create you own pirate ship.



Tooling the ship:
Select a tool that meets your needs. In this case, I have selected a flat tool with a rounded end. I find that even though I have dozens of tool, I tend to use on a selected few for most projects. Pick out a few that you like, and keep these aside from the rest. This will save time and it will help you become proficient as you learn to use each of these selected tools. As you learn to effectively use each specialised tool, your crafting skills will improve.

Using the flat, rounded end, I will run the tool at an angle along the bottom edge. As you guide the tool, small shavings of clay will be removed. Be carful not to dig into the seam and remove too much. Most of the tooling will be smoothing the clay over.

Continue to work the edge on both sides, taking care at the bow as you shape the smooth curves of your ship. The purpose of this step is to form a seamless bond along the base of the sides, and removing any excess clay that would form lumps on the sides of the ship.

=> Use your center line while working the edge to keep the shape of the hull symmetrical.

Smooth the bottom:
Carefully flip the ship over. If the clay has bonded to your working surface, use a flat putty blade, or very thin (dull) knife to gently remove the clay. Be careful not to cut into the bottom.

With the same flat rounded tool used above, gently smooth the bottom seam. I like to use a brush stroke like movement, blending at a 45-degree angle to the seam. Make sure you smooth the entire edge, then return the ship upright.

Add clay as needed:
I find that certain areas require a dab of clay to reinforce the ship. By adding a small ball of clay into the bow for example, I help strengthen the bond formed at the prow of the ship.

Work the clay into the seam, and smooth the edges until you form a nice even surface in the bow of the ship.
This area will later be covered by the forecastle deck, however the extra clay will help hold the model together.

Cutting pieces for the Stern:
Flatten the clay with your rolling pin, this time keeping the clay about 5/8" inch thick. The two pieces shown to the left are the stern, and a small piece of the quarter deck that will be used to bond the stern to the quarterdeck.
=> This small portion of the quarterdeck is later used to mount the ships wheel.
  • The quarter deck itself is going to be a removeable piece, so it will be built independantly in a later installment.

Assemble the Stern:

The pattern for the stern was also folded in half to help form a center line on the clay piece. This center line is then used to match up the main deck with the stern piece.

As you match up the stern, gently pinch the two pieces together. Take care not to pinch too hard, you do not want to damage the shape of the gunwale or the stern pieces.
=> Use a heavy card stock for your patterns, it helps ensure they will last for more than one ship. Notice the center line on the hull, formed by pressing the center fold in the card stock pattern into the clay.

Smooth out the Stern:
From the inside, you will then bond the two peices together using a flat tool. In this case, I have blended the clay starting from the gunwale and blending the clay onto the stern piece. This will be the first step in forming a seamless bond, which will hold the two pieces together.

=> This is an area that I would suggest you add some clay to help strengthen the bond.


Adding a bead of clay:
Roll up a bead of clay that will be used to along the seam formed between the main deck, the two gunwales and the stern.
With your fingers first then with your tools, work this bead into the seam.
You will want to blend the bead onto the main deck, the two gunwales and onto the stern piece to form a smooth bond.
It is critical to thouroughly work these seams together, this bonds the clay, stregthening the overall model.
=> Add a second bead as needed.
Shape the Stern:
With a flat tool, from the stern to make it appear that it was built with two separate pieces. You will note that I have pushed the bottom of the stern, squaring it off in the aft section.
In addition, I have pinched the bottom edge and the two edges that bond the gunwale/side together to form a "squared" stern.
Later you will add the rudder enclosure, and detail the stern section. For now just make sure it is rounded on top, and squared off on the bottom section of the stern.
Preparing the Quarterdeck:
Add the small 1/2 rounded piece of the quarterdeck. You will notice in the background the pattern for this 1/2 rounded quarterdeck section, in addition to the quarterdeck pattern, and bulkhead pattern.
Smooth the 1/2 rounded piece into the rounded section of the stern, and blend the seam into the two gunwale/sides.
Also use your tools to bond the underside of the this 1/2 rounded section. Since it will be hidden from view, I suggest you add a bead of clay and work it into the seam underneath the quarterdeck section.
Concluding part 2:
Your ship is now prepared to add the removable quarterdeck, which will be outlined in the next installment.
You will notice how the stern has a nice rounded shape, and the small section of the quarterdeck is squared off.
As you form the quarterdeck section, you will custom build the pieces to match this shape.
For now this concludes part TWO of the Pirate Ship build.
In the next installment I will illustrate how to build the removable Quarterdeck section.
John T Cusack
Posted by Picasa